What should I do if my washer is not spinning properly?

washer water inlet

Are you having trouble with your washer not spinning as it should? This can be a frustrating and inconvenient problem to have. Fortunately, there are several common issues that can cause this problem and solutions you can try. In this section, we will provide troubleshooting tips to help you resolve your washer spin problems.

Key Takeaways

  • Washer not spinning properly? Don’t panic! There are several things you can do to troubleshoot the issue.
  • Check for proper leveling and examine the load size to avoid an unbalanced washer.
  • Inspect the drive belt, motor coupler, lid switch, and motor brushes for any issues.
  • Clean the drain pump filter and verify proper water inlet.
  • If all else fails, seek professional assistance from a reliable washer repair service.

Check for proper leveling

Is your washer not spinning as it should? One possible reason could be an unlevel surface. Ensuring your washer is properly leveled can help solve this issue.

To check if your washer is level, use a bubble level on top of the washer, in both the front-to-back and side-to-side directions. If the bubble isn’t centered, adjust the washer’s feet until it is level.

If your washer continues to be unbalanced, consider placing a plywood board under the machine to help distribute weight.

Proper leveling can prevent an unbalanced washer, which in turn can help avoid spinning problems and extend the lifespan of your washer.

Examine the Load Size

One of the most common reasons for a washing machine not spinning properly is overloading. It’s important to remember that washing machines have weight limits for a reason. Ignoring these limits can lead to a variety of problems, including an unbalanced load, which can prevent your washer from spinning as it should.

To determine if you’re overloading your washer, start by reading the manufacturer’s manual for specific guidelines on weight limits. Also, consider the size of your laundry basket. Just because you can fit a certain amount of clothes in your basket, it doesn’t always mean you should put them all in the washer at once.

As a general rule of thumb, you should fill the washer drum about three-quarters of the way full. This will allow the clothes to move freely during the wash and spin cycles, which will help prevent overloading and other spinning issues.

If you’re unsure about the load size, try doing a test run with a smaller load. This will help you determine if the load size is the problem and will give you a chance to adjust accordingly.

Remember, overloading your washer can cause a variety of issues, not just spinning problems. It can also lead to damage of the washer’s drum and other components.

How to Avoid Overloading Your Washer:

  • Weigh your laundry before adding it to the washer
  • Don’t pack your clothes too tightly into the washer
  • Follow the manufacturer’s weight limit guidelines
  • Separate heavy items like towels and blankets from lighter clothing

By following these guidelines, you’ll avoid overloading your washer and keep it working properly. If you continue to experience spinning issues, it may be time to move on to the next troubleshooting step.

Inspecting the Washer Drive Belt

If your washer is not spinning properly, it could be due to a worn-out or damaged drive belt. Inspecting and replacing the drive belt is a relatively simple process that can be done at home. Here’s how:

  1. Unplug the washer and turn off the water supply before beginning.
  2. Locate the drive belt, which is typically found behind the front panel of the washer.
  3. Check the belt for any signs of wear and tear, such as cracks or frayed edges.
  4. Ensure that the belt is properly aligned and tensioned. The belt should have about ½ inch of play when pressed firmly in the center.
  5. If the belt is worn out or damaged, purchase a replacement belt from your local home improvement store or online retailer. Refer to the manufacturer’s instructions for the appropriate belt size and installation process.
  6. Carefully remove the old belt and replace it with the new one, following the manufacturer’s instructions.
  7. Reinstall the front panel of the washer and plug it back in.
  8. Start the washer and check to see if it is spinning properly.

If the washer is still not spinning properly after replacing the drive belt, it may be necessary to call in a professional for further assistance.

Check the Motor Coupler

If your washer is not spinning properly, the motor coupler may be broken or damaged. The motor coupler connects the washer’s motor to the transmission and helps to turn the drum. Here’s how to check the motor coupler:

  1. Unplug the washer from its power source and turn off the water supply.
  2. Locate the motor coupler, which is typically found near the bottom of the machine.
  3. Visually inspect the motor coupler for any signs of wear or damage.
  4. If the motor coupler is broken, it will need to be replaced. You can purchase a new motor coupler online or from an appliance parts store.

Replacing the motor coupler can be a challenging task, especially for those who do not have experience working with appliances. If you’re uncertain about replacing the motor coupler, it may be best to consult a professional for assistance.

Keep in mind that if the motor coupler is not the issue, there may be other underlying causes for your washer’s spinning problem. Check out the other sections of this article for more troubleshooting tips.

Examine the lid switch

A faulty lid switch can prevent your washer from spinning correctly. This switch is responsible for detecting whether the lid is closed, and if it detects that the lid is open, it will not allow the washer to spin. If the lid switch is faulty, it may not detect that the lid is closed, or it may detect that the lid is open even when it is closed.

To test the lid switch, you will need to access it by removing the top of the washer. Once you have located the switch, use a multimeter to test its continuity. If there is no continuity, the switch is faulty and needs to be replaced.

If you need to replace the lid switch, you can refer to your washer’s manual for instructions. Generally, you will need to disconnect the wiring harness and remove the screws holding the switch in place. Then, install the new switch and reconnect the wiring harness.

Tip: Always unplug your washer before attempting to access or replace any components.

Clean the drain pump filter

If your washer is not spinning properly, a clogged drain pump filter could be the culprit. The drain pump filter is responsible for removing debris from the washer’s drainage system, but over time, it can become blocked with hair, lint, and other materials.

To clean the drain pump filter, follow these steps:

  1. Locate the filter, which is typically located at the bottom of the washer.
  2. Place a towel or bucket underneath the filter to catch any water that may spill out.
  3. Turn the filter counterclockwise to remove it from the washer.
  4. Clean the filter thoroughly, removing any debris or buildup.
  5. Reinsert the clean filter and turn it clockwise to secure it in place.

If the drain pump filter was the cause of the spinning issue, your washer should now operate as expected. However, if the problem persists, it may be necessary to explore other possible solutions.

Pro tip: It’s a good idea to clean the drain pump filter every six months to prevent buildup and keep your washer running smoothly.

Check the motor brushes

If your washer is not spinning correctly, worn-out motor brushes could be to blame. Motor brushes are responsible for conducting electricity to the motor, and over time they can become worn and need replacing.

Here are the steps to check the motor brushes:

  1. Unplug the washer from the power source.
  2. Locate the motor brushes. They are typically located near the bottom of the motor.
  3. Remove the motor brush caps by gently prying them off. Some washers have screws that need to be removed first.
  4. Inspect the motor brushes for any signs of wear or damage. If the carbon brush is worn down to its indicator line, it needs to be replaced.
  5. If the motor brushes need to be replaced, use a screwdriver to remove the screws holding them in place.
  6. Insert the new motor brushes and tighten the screws.
  7. Replace the motor brush caps and secure them in place.
  8. Plug the washer back in and run a test cycle to ensure the motor brushes are working correctly.

If you are unsure about checking or replacing the motor brushes, consult a professional washer repair technician. They will be able to ensure the job is done correctly and safely.

Test the motor control board

If you have checked all the other components and still cannot identify the problem, the issue may lie with the motor control board.

The motor control board is responsible for controlling the motor speed and direction. If there is a fault in the board, it can cause the washing machine’s motor to malfunction. To test the motor control board, follow these steps:

  1. Make sure the washing machine is unplugged.
  2. Locate the motor control board. Depending on your washing machine’s make and model, the motor control board may be located at the back of the washing machine or under the control panel.
  3. Check the motor control board for any signs of damage or burnt components.
  4. Use a multimeter to test for continuity between the different terminals on the motor control board.
  5. If the motor control board is faulty, it will need to be replaced.

If you are not comfortable with testing or replacing the motor control board yourself, it is best to seek the assistance of a professional washer repair technician. They will be able to diagnose and fix the problem for you.

Verify Proper Water Inlet

Low water pressure can be a common cause of washing machine spinning problems. If you have ruled out the previous troubleshooting steps outlined in this article and are still experiencing spinning issues, it’s time to verify the proper water inlet.

The water inlet valve is responsible for controlling the water flow into the machine. If the valve is not open or has low water pressure, the machine will not have the necessary amount of water to complete the spin cycle.

To check the water inlet, turn off the water supply and disconnect the hoses from the back of the machine. Check for any clogs or debris that may be blocking the water flow. Clean the inlet screens thoroughly and reconnect the hoses, ensuring they are securely tightened.

If the water inlet is clear and the issue persists, it may be necessary to call a professional repair technician to further diagnose the problem.

Regular maintenance of your washing machine, including cleaning the water inlet and checking for leaks, can prevent spinning problems and extend the life of your machine. Remember to always follow the manufacturer’s instructions and take safety precautions when working with electrical or plumbing components.

Seek Professional Assistance

If you have followed all the troubleshooting steps and your washer is still not spinning properly, it may be time to seek the help of a professional repair technician.

A washer repair service can provide diagnostic tests to identify the root cause of the issue and suggest the most effective solutions. Additionally, a repair technician can inspect and replace parts, ensuring that your washer is functioning correctly and efficiently.

When choosing a repair service, make sure to select a reputable company with experience in washer repair. Look for online reviews and ask for referrals from friends and family. It is also important to inquire about the service cost and any warranties or guarantees offered.

Remember, attempting to fix complex issues without the proper skills and tools can result in further damage to your washer. Seeking professional assistance can save you time, money, and frustration in the long run.

Max Appliance Repair

Written by Max | An appliance repair technician with more than 15 years experience in appliance repair services in Toronto and the GTA.

Disclaimer: This post "What should I do if my washer is not spinning properly?" is for information purposes only. If you need specific help, please contact Max Appliance Repair at https://maxfix.ca/contact/.